wayne dalton idrive garage door opener conversion

#WAYNE DALTON IDRIVE GARAGE DOOR OPENER CONVERSION HOW TO#
#WAYNE DALTON IDRIVE GARAGE DOOR OPENER CONVERSION INSTALL#

Q: What is the gauge of wire used for the wired Photoelectric Sensors and Pushbuttons? Q: My garage door opener will work using the button on the wall in the garage, but the remote for the car will not work. The Trolley travels a short distance from the Open position and reverses. Q: I've programmed my Wireless Photoelectric Sensors. Q: I have lost the instructions for my keypad.

#WAYNE DALTON IDRIVE GARAGE DOOR OPENER CONVERSION HOW TO#

Q: How to Select the Correct Remote Control or Keypad Q: How many Keyless Entry pads can I program to my unit? Q: How many garage door openers can I program with one Keyless Entry Pad? Q: How do I program two transmitters to the same opener? Q: How do I program my Wireless Photoelectric Sensors? Q: How do I make my Wayne Dalton Classic Drive model 3012, 3016 Opener work with my built-in car remote control? Q: Hand-held remote (Transmitter) will not program. Q: Door hesitates during downward travel when activating my Wireless unit Q: Do you have a one button transmitter for a wayne dalton classic drive model 3012? Q: Can I use my Transmitter (remote) from another opener with the Wayne-Dalton opener? The information provided above is a troubleshooting guide provided by the manufacturer Wayne Dalton.Solution home FAQ Wayne Dalton Classic Drive We do not offer warranty service, or technical help with this opener. PLEASE NOTE: We are not the manufacturer of this unit. Replacement sensors can be purchased here. Photo beams must have a solid red LED light on at all times. Check alignment of photo beams as well as wiring at operator. From open position door will not close and I get 3-4 beeps. When I press Wall Station I get no door movement and motor won’t start and operator beeps 6 times.ĭamaged Motor Control Board. Position potentiometer nut 1/8 – 3/16 “ from left stop of motor control board when door is closed.ġ0. Potentiometer nut out located on motor control board of adjustment. It goes up, down, up and stops and I get 4 beeps.

#WAYNE DALTON IDRIVE GARAGE DOOR OPENER CONVERSION INSTALL#

When I run an install routine it does not complete 2 up and down cycles. Disconnect opener and manually pivot motor up to check.ĩ. Adjust detent pin in/out so right hand tip just touches face of motor bushing. My motor will not pivot up or will not stay up.ĭetent pin is out of adjustment. If handle is engaged and operator makes a grinding sound internal drive gear is stripped. When I try to open my door motor runs but door does not move.

If door is heavy and falls order a spring replacement here.ħ. Door should open and close easily and stay in any position it is raised to. Ensure there are no children or pets in the area of the door. Pull red emergency release handle on right hand side of door and lock into bottom of bracket. When I press up/down button again door closes.Ĭheck door balance. Check motor connection to operator or replace operator. When I press my Wall Station to open or close door I get one beep.

When I press my Wall Station to open or close door operator responds with a 1 second, then ½ second beep followed by a chirp and no operator start. Replace battery or batteries in the remote and reprogram remote. One of my hand held remotes does not work but others do. Operator will beep once indicating it is out of vacation mode.ģ. Move the vacation switch located under the cover on wall station down to lock then back up to unlock. When I press the button to open the door the iDrive chirps 5 times and overhead light flashes. If iDrive has power and no audible beeps are heard Motor Control Board must be replaced. Verify power at outlet, check the connection at receptacle, check connection at operator. My iDrive TorqueMaster will not respond to wall station or remotes and there is no audible feedback from operator. You will have to contact a local garage door company to figure out what options are available for you.ġ. If this is the case you are going to need to replace your opener completely. We have not been able to get them for a few years now. If you need to replace the control board, motor, or gear drive you will not be able to acquire those parts (check ebay). The internal parts for this unit are out of production. Please Note: Wayne Dalton no longer manufactures openers.

Wayne dalton idrive garage door opener conversion